ULTIMIX

 

Installation & Maintenance:

UltiMix Series

IMPORTANT - Please read

"ULTIMIX" dispenses BOILING water – Please treat with care.
Do not use the "ULTIMIX" for washing hands

Important: this unit must be installed by an authorised plumber.
Warning: unit is to be connected in accordance with as3500.4.1 or as/nzs 3500.4.2
Supply pressure minimum – 200 Kpa, maximum – 2000 Kpa
Supply temperature – 5 deg to 35 deg
This unit is fitted with a computerised element and boil dry protection.
Altitude will alter temperature (refer back to manufacturer)
Warning: Do not switch on power until water runs out of tap.

* Rapid action ¼ turn tap handles
* No drainage or overflow is required
* The tap vents through the tap spout

Components supplied with the unit;

  • Chiller unit

  • Boiling water unit

  • Tap dispenser

  • Aquaknect flexible connector – 450mm long (Do not over tighten)

  • Combined dual check valve with 350 Kpa PLV (Connected to boiling water unit)

* If fitted with filter we recommend changing the cartridge every 6 months
* The manufacturer recommends the cleaning and service of the unit every 12 months
* IF SUPPLIED CORD IS DAMAGED IT MUST BE REPLACED BY AN AUTHORISED SERVICE AGENT (ELECTRICIAN).

Please leave these instructions with the owner.

 

Installation instructions – model ULTIMIX series

Do not plug in or turn on power - Unit must be positively earthed

  1. Position the tap head on a flat area in an appropriate location (i.e. Tea room sink), Drill 38mm diameter hole, washer supplied.
  2. Position boiling water unit underneath the sink directly beneath the tap head.
    1. Observe attached labels (ensure when pipes are cut – deburr ends before fitting).
    2. Connect 5/16” outlet from the tap head spout to the boiling water unit, NB: The pipe must not be extended and must have continuous fall between tap and boiling water unit.
    3. Connect inlet pipe from the tap body to the boiling water unit (inlet).
    4. Connect main water supply from the tap body to the outlet side of the filter head.
    5. Connect the 3/16” nylon tube from the tap to the 3/16” copper vent pipe on the boiling water unit. (heat nylon tube ends in boiling water to ensure easier fitting).
    6. Position the chiller unit adjacent to the boiling water unit with a minimum clearance between the units of no less than 50mm.
    7. Connect inlet and outlet pipes from the tap head to chiller unit as per markings.
    8. Connect aquaknect flexible hose to PLV (inlet side of the filter head).
  3. Open both taps until the water is flowing from both spouts. 18 litres of water must be flushed through filter before turning on power.
  4. Plug units into the power point and switch on.
Please note: When fitting this unit in a cupboard of small proportion, please note that these units omit heat. If in doubt install cross flow vents.
Warning: Do not connect to hot water line – to do so will void warranty.

TYPICAL INSTALLATION

ultimix install

 

 

TROUBLE SHOOTING
Action to be performed by a qualified person.
BOILING WATER UNIT

SYMPTOM CAUSES ACTION
No Water Water supply turned off Check mains supply
Blocked Filter Replace Cartridges
Water not hot Faulty element and computer Replace dual computerised element
No power supply Check and test power supply
Water overflowing from tap spout Expansion chamber full Run tap for 5 – 10 mins, this will correct water level in expansion tank
Low inlet pressure Contact manufacturer
Boiling On Replace element
Excessive steam from tap Fault element Replace element
The boiling water unit is designed to have no less than 150ml off at any one time.

 

 

TROUBLE SHOOTING
Action to be performed by a qualified person.
CHILLED UNIT

SYMPTOM CAUSES ACTION
No water Water supply turned off Check mains supply
Blocked Filter Replace cartridges
Water not cold Thermostat Not set correctly
Loss of gas Contact manufacturer
Failed fan Contact manufacturer
No power supply Check and test power supply
Poor ventilation Clean cabinet louvers (if fitted) & condenser fins - these units need ventilation
Faulty element

Replace element

Australian Service Agents

New South Wales

Boiling Billy

Click to view full details

Contact: Tania Wiffen

Phone: +61 (0) 3 5248 7072
Fax: +61 (0) 3 5248 7272

Email: This email address is being protected from spambots. You need JavaScript enabled to view it.

1/33 Cedar Parade, Moolap, VIC, 3224

Northern Teritory

Boiling Billy

Click to view full details

Contact: Tania Wiffen

Phone: +61 (0) 3 5248 7072
Fax: +61 (0) 3 5248 7272

Email: This email address is being protected from spambots. You need JavaScript enabled to view it.

1/33 Cedar Parade, Moolap, VIC, 3224

 

Queensland

Mark Anderson Sales

Click to view full details

Phone: (07) 3890 8011
Fax: (07) 3890 8022

Building 4, 84 Ingleston Rd, Wakerley, QLD, 4154

 

South Australia

Boiling Billy

Click to view full details

Contact: Tania Wiffen

Phone: +61 (0) 3 5248 7072
Fax: +61 (0) 3 5248 7272

Email: This email address is being protected from spambots. You need JavaScript enabled to view it.

1/33 Cedar Parade, Moolap, VIC, 3224

 

Tasmania

Boiling Billy

Click to view full details

Contact: Tania Wiffen

Phone: +61 (0) 3 5248 7072
Fax: +61 (0) 3 5248 7272

Email: This email address is being protected from spambots. You need JavaScript enabled to view it.

1/33 Cedar Parade, Moolap, VIC, 3224

 

Victoria

Interchange Sales And Marketing

Click to view full details

Contact: Kevin Cottom

Phone: (03) 9729 6411
Fax: (03) 9729 5722
Mobile: 0415 934 913

Unit 4, 49 Corporate Blvd, Bayswater, VIC, 3153

 

Western Australia

Pride Industries

23 Munt Street
Bayswater WA 6053

Ph: 08 9272-6511  Fax: 08 9272-3427

Email: This email address is being protected from spambots. You need JavaScript enabled to view it.

Complete Enviro Solutions

Contact: Ken

Mobile: 0429 028 285

Contact: Ryan

Mobile: 0408 363 645

Click to view full details